NETGEAR's ProSafe FS752TS deliver performance and scalability through a 4Gbps, dual-ring, resilient stacking architecture with the ability to mix and match to stack up to six units or 192 10/100 ports and manage them all at a single IP address. The non-blocking design of the switches deliver simultaneous, full wire-speed, low-latency throughput to all ports. Shipped ready to go straight out of the box, they deliver switching that's easy to set up, stack-up and use.
|
| Manufacturer |
Netgear, Inc |
| Manufacturer Part Number |
FS752TSNA |
| Manufacturer Website Address |
www.netgear.com |
| Brand Name |
Netgear |
| Product Line |
ProSafe |
| Product Model |
FS752TS |
| Product Name |
ProSafe FS752TS 48 Port 10/100 Stackable Smart Switch |
| Product Type |
Stackable Ethernet Switch |
| Interfaces/Ports | Number of Ports | 48 |
| Fast Ethernet Port | Yes |
| Interfaces/Ports | 48 x RJ-45 10/100Base-TX LAN
4 x RJ-45 10/100/1000Base-T |
|
| Media & Performance | Connectivity Media | Category 5 Twisted Pair 10/100/1000Base-T |
| Performance | 17.6Gbps Bandwidth |
|
| I/O Expansions | Number of Expansion Slots | 2 |
| Expansion Slots | (2 Total) SFP |
|
| Network & Communication | Flow Control | IEEE 802.3x (Full-duplex)
Back Pressure (Half-duplex) |
| Switching Method | Store-and-forward |
| Layer Support | 2 |
| Number of Stacks | 6 |
| Address Table | 8K MAC Address - Per System |
|
| Management & Protocols | Manageable | Yes |
| Management | IEEE 802.1Q VLAN (128 groups, Static or Dynamic)
IEEE 802.1p Class of Service (CoS)
Port-based QoS
SNMP v1, v2c, v3
MIB II
Ethernet Interface MIB
Bridge MIB
DHCP client
Storm control for broadcast, multicast and unknown unicast packets
Port-based ingress/egress rate limiting
SNTP
RMON group 1, 2, 3, 9
Private Enterprise MIB
Port Mirroring Support
Web-based configuration
Configuration Backup/Restore
Password Access Control
Firmware upgradeable |
| Protocols | SNMP v1
SNMP 2c
SNMPv3
LACP
DHCP
SNTP |
| Security Features | Port-based security by locked MAC addresses
801.x security |
|
| Controls/Indicators | Status Indicators | Unit: Power, Master, Stack ID
Per Port: Link, Speed, Activity
Per Gigabit Port: Link, Speed, Activity, Stack |
|
| Reliability | MTBF | 84000Hour |
|
| Power Description | Input Voltage | 110V AC
220V AC |
| Input Voltage Range | 100V AC to 240V AC |
| Frequency | 50 Hz or 60 Hz |
| Power Consumption | 15 W @ Maximum |
|
| Environmental Conditions | Temperature | 0 °C (32.0 °F) to 50 °C (122.0 °F) Operating
-20 °C (-4.0 °F) to 70 °C (158.0 °F) Storage |
| Humidity | 90% Maximum Non-condensing Relative Humidity Operating
95% Maximum Non-condensing Relative Humidity Storage |
| Altitude | 10000 ft Operating
10000 ft Storage |
|
| Physical Characteristics | Dimensions | 1.7" Height x 17.8" Width x 8.1" Depth |
| Weight | 6.57 lb |
|
| Miscellaneous | Package Contents | ProSafe 48 Port 10/100 Stackable Smart Switch
Rubber footpads
Power cord
Rack-mount kit
Resource CD Installation Guide
Warranty/Support information card |
| Additional Information | Network latency: Less than 20 microseconds for 64-byte frames in store-and-forward mode for 100 Mbps to 100 Mbps transmission.
Addressing: 48-bit MAC address |
| Certifications & Standards | IEEE:
IEEE 802.3
IEEE 802.3u
IEEE 802.3ab
IEEE 802.3z
IEEE 802.3x
Electromagnetic Compliance:
CE mark, commercial
FCC Part 15 Class A
VCCI Class A
EN 55022 (CISPR 22)
EN 55024 (CISPR 24)
C-Tick
Safety:
CE mark, commercial
CUL 60950 (Listed)/ EN60950 (Low Voltage Directive)
RFC:
RFC 1213
RFC 1643
RFC 1493
RFC 2131 |
|
| Warranty | Lifetime |
|
